slave controller
英 [sleɪv kənˈtrəʊlə(r)]
美 [sleɪv kənˈtroʊlər]
网络 附属控制器; 从控制器; 从属控制器; 控制器; 从动控制器
双语例句
- The proposed control structure consists of a slave system and a master controller.
控制系统包括主控制器和从系统两部分。 - A design method of slave system fuzzy controller for AC servo system in radar is presented with fuzzy control theory.
结合模糊控制理论，针对雷达的交流伺服系统，提出了随动系统模糊控制器的设计方法。 - Design of a USB 2.0 Slave Controller
USB2.0协议从控制器设计 - In this paper, a Linux-based embedded intelligent control platform with low cost and high performance is designed. This platform includes a mastery Linux-based embedded controller and a slave controller with USB interface and meets the need of distributed 2-layer control system which is widely in industrial control.
本文基于Linux的嵌入式智能控制器平台研究开发的目标是设计出低成本、高性能的Linux嵌入式主控制器和采用USB接口的从控制器，以应用于工业控制中广为运用的分布式二级控制系统。 - The Design of PROFIBUS-DP Slave Station Link Layer Controller based on FPGA
基于FPGA的PROFIBUS-DP从站链路层控制器IP核的设计 - After that a master DAMA controller and three slave DAMA controller and subscriber interface equipments have been accomplished.
在此基础上完成了一个主DAMA控制器和三个分站DAMA控制器及用户接口设备的研制。 - A Design of Airborne VME Slave Controller Based on CPLD
基于CPLD的机载计算机VME总线从方控制器设计 - As slave control part, sub-user controller calculates and temporarily stores power sent from measuring module;
从控部分子用户控制模块计算并暂存电能测量模块输出功率数据； - As for the hardware, a PC-based host-slave control system, with a digital signal processor ( DSP) as the slave controller was developed in the need of high-speed servo.
在硬件上开发了满足高速伺服需求的、基于工业PC和数字信号处理芯片（DSP）的主从控制结构。 - By using MOXA multiport serial board with its function of communicating with multiple slave computers or devices when implementing process control, the development of serial communication in process controls including temperature controller with Microsoft Visual Basic developing platform is described in detail.
借以MOXA多串口卡在工控同时与多台下位机或设备进行串口通信中的应用，深入讨论了在微软VISUALBASIC开发平台上开发控制中的串口通信的实现方法，包括与温控仪的通信。 - In this paper, the function of USB slave controller is presented and its module constitution of a solution is introduced.
文章介绍了USB从控制器所要完成的功能和一种实现方案的模块构成，并且说明了实现USB协议的处理流程。 - I Designed servo to control different types slave hands that has three freedom degree, position controller hydraulics.
分别针对从手的各自由度，通过主从位置控制试验来验证所设计的位置控制器的合理性及有效性，以及所使用的控制算法的正确性。 - We developed the special controller as the SLAVE controller unit based on the practical need.
本文根据芯片实际应用的要求，为其开发了专用的控制器，作为总线的SLAVE控制单元。 - And LIN bus communication is implemented by asynchronous serial communication between master node and slave node, while CAN bus communication is implemented by the CAN controller inside the microcontroller between the master node and other nodes.
主节点和从节点之间采用异步串行通信方式实现LIN总线通信，主节点同车身其他控制节点的之间通过单片机内部的CAN控制器来实现CAN总线通信。 - The lower controller composes of detection slave controllers, receiving data host controller ( host controller 1) and sending data host controller ( host controller 2).
下位机由检测从机和数据接收主机（主机1）和数据发送主机（主机2）构成。 - The function of detection slave controller is to sample current, and with A/ D transmission circuit and current sensor compose of current detecting circuit.
检测从机主要用于检测电流信号，与电流传感器和A/D转换电路组成电流信号采集电路。 - The upper node is a computer, while the slave part contains the USB-CAN interface card, micro controller, CAN controller, the can bus transceiver some specific sensors.
上位机有PC担任，下位机则包含了USBCAN接口卡、微控制器、CAN控制器、CAN总线收发器及一些具有特定用途的传感器。 - The hardware of master and slave modules uses embedded ARM processor with CAN controller as their core CPU and uses the real time operating system& μ C/ OS-ⅱ as their software designing platform.
主/从站硬件采用带有CAN控制器的嵌入式ARM处理器作为它们的核心，并采用μC/OS-Ⅱ嵌入式实时操作系统作为软件开发平台。 - Host computer software development is entirely based on MFC platform to complete the wave file generation and the control of slave controller.
上位机软件完全基于MFC开发平台，完成上位机波浪文件的生成及对下位控制器的控制。 - Because of the specialties of the IP design, driver designer should consider the route switch between the high-speed and the full speed controller, access to shared buffer, and the mode of ARM accessing the IP core as a slave.
由于IP硬件设计的特殊性，主机控制器驱动的设计需要考虑到高速与全速控制器的路由切换与缓存区的共享，以及ARM访问作为SLAVE的IP核的方式。